A brushless motor inside the brushroll
- Placed a small brushless DC motor inside the brushroll and optimized RPM and brush engagement with the floor

Mechanical Design Portfolio
Senior Mechanical Engineer in new product & advanced development. I take consumer products from first concept to mass production, balancing performance, cost and form.
Six Shark products I engineered at SharkNinja, in launch order: five cordless vacuums and a hot air brush. Every image is a launch render or product photo.
Cordless VacuumNew Floorhead

Shark's first motor-in-roll floorhead
A completely new floorhead architecture sized for Japan, where products have to meet low weight and size targets with a premium look and feel without compromising on performance. At launch it was the smallest floorhead Shark ever made.


Cordless VacuumTechnology Integration

Dirt detection that sets suction automatically
The follow-up to Japan’s Gen 2 WandVac added IR sensors to detect debris and modulate suction power as needed for best cleaning and longer runtime, plus a new animated UI and hidden headlight.



Cordless Vacuum & Auto-Empty DockNew Platform

A new product line built from the ground up
Pair the convenience of a Shark WandVac with cleaning performance that competes with the larger legacy vacuums, and give it Shark's first auto-empty dock specifically designed for cordless vacuums.



Cordless Vacuum & Auto-Empty DockDock Redesign

A complete dock redesign: cheaper, smaller and better
The original dock had too much unused space around the duct and dust bin. Reorienting the layout freed that space and improved nearly every metric with the same bin volume. The design was adopted across the entire product family.



Air paths split around the bin, leaving dead volume at the corners.


Rotating the layout put the duct, bin and air path in line and minimized the unused space.
Cordless Vacuum & Auto-Empty DockNew Platform

Applying the lessons: a smaller floorhead and a smarter dock
Shark's second pistol-grip system carried over the motor-in-roll and dock work from earlier programs, then pushed size, cost and bare-floor cleaning further.


Hot Air BrushNew Platform

The industry's first hot air brush with the heater in the brush head
Moving the heater out of the handle and into the head made room for a smaller handle that is easier to grip than competing hot air brushes.


About

I'm a senior mechanical engineer with more than ten years of experience across consumer products, aerospace, military and automotive. At Midea America I'm the lead engineer on new product platforms. Before that I spent nearly four years at SharkNinja taking Shark Cordless and Hair Care products from R&D to mass production. The products on this page come from that work.
Leadership has been part of my job for years. I give technical direction and mentorship to the engineers on my programs, and I work as the right hand to a director-level platform leader. At SharkNinja I led cross-functional project teams, managed direct reports, and spent six weeks covering for a senior director responsible for two product groups.
I'm drawn to problems where performance, cost and form all pull against each other: packaging motors, sensors and lighting into tight spaces, designing mechanisms that make a product easier to use, and redesigning to cut cost while improving performance. I like working directly with executives, industrial design, marketing and quality teams to get every requirement into one product within a rapid development cycle.
Leadership
Technical
Experience
Midea America · Waltham, MA
Lead engineer on new product platforms. Took a patent-pending technology from concept to tooling that a major brand bought for its products, and drove two more patentable technologies to full validation.
SharkNinja · Needham, MA
Led project teams of up to 5 engineers on Shark Cordless and Hair Care. Managed an engineer and two co-ops, and covered for a senior director over two product groups for six weeks. Launched a new cordless platform in 9 global markets with patented technologies I developed and multiple best-in-class claims.
AMETEK · Wilmington, MA
Owned fluid sensing and mass flowmeter products. Designed a jet-fuel-compatible plug that solved flowmeter contamination and saved an estimated $74K a year.
Stoneridge · Canton, MA
Owned electromechanical product families with over $36M in annual sales. Delivered a patented trailer tow connector that uses a Hall-effect sensor to detect its cover position, supporting autonomous cruise control.
QuEST Global · South Windsor, CT
Aerospace consulting. Led nozzle wear validation for the F-35 engine program and raised compressor rotor life 150% by reworking cross-section geometry.
Worcester Polytechnic Institute
Patents